Manual

Smart Laser CO2

このエントリーをはてなブックマークに追加

Introduction

When your Smart Laser CO2 arrives, first please check the contents of the package.

Smart Laser CO2 Packing list of the Smart Laser CO2

Tools to be prepared by the customer.

Smart Laser CO2 Option packing list

Tools to be prepared by the customer.

Contact

Please contact smart DIYs if there are any discrepancies in the described contents or any missing pieces. In the rare case this may occur, please include the product number in your inquiry.

Tools used for assembly

The Smart Laser CO2 requires the following tools for assembly.

Please prepare following tools

 

  1. Phillips screwdriver
  2. Hex wrench
  3. Spanner
  4. Pliers
  5. Ruler ・Scale
  6. Nipper・Scissors
  7. gloves
  8. Level gauge

 

Caution・Warning

 

Assembly

・This product is an assembly kit and requires parts supply. Please read the manual beforehand.
・The edge of the acrylic is very sharp. Please be careful and wear gloves when handling.
・Do not operate the device when screws and nuts are loose.
・Please read the manual beforehand to determine whether it is feasible for you to assemble.
・We do not offer services to assemble the products.

Handling of the laser

・The laser radiation is very harmful. Please use extreme caution against possible fire, burns or injury to the eyes.
・Do not turn the power on until assembly is completed.
・Do not let the laser light enter the eyes directly or by reflection.
・Be sure to use protective glasses applicable for the laser wavelength being used.
・Never look directly at the laser radiation even when using protective eye wear or at low laser intensities.
・Do not place highly reflective items near the laser.
・Do not direct the laser radiation on any part of the body, even through clothing.
・Do not direct the laser radiation on items other than the intended work piece or toward other individuals.

Operational handling notes

・Laser Tube must be cooled. Please use Cooling System for Laser Tube for Smart Laser CO2 or other cooling devices sold at stores. Damages caused by not using the cooling system will not be covered under warranty.
・An air assist pump is required when processing materials that emit fire or smoke. If you do not purchase the air assist pump, please take safety measures for fires.
・Repair, maintenance, and operation of the Smart Laser CO2 should be performed only by people familiar with the dangers.
・Please use the laser cutting machine where there are no flammable, combustible, or volatile substances.
・Do not use on materials such as polyvinyl chloride, nylon, Teflon, polyurethane or other materials which will give off toxic gases.
・Ventilate well to allow smoke generated in the laser cutting process to escape.
・Operate the laser cutting machine after confirming there are no children in the vicinity.
・Do not move the laser cutting machine while it is in operation.
・As there is a risk of fire, please make sure that rubbish does not stuck below the manufacturing bed.
・When While calibrating the system, please make adjustments without looking into the mirrors.
・ Please adjust the optical axis if you moved the Smart Laser CO2 even slightly.
・Do not leave the machine while it is in operation.
・Do not look directly at the radiation when processing.
・Make sure that the Smart Laser C02 is always grounded using a 3-pin AC cable, or other grounding wire.

Product warranty

・Please contact us within 30 days of delivery in a case of missing or defective parts. We will repair or replace at free of charge. Due to the nature of the product, the warranty only covers initial defects for parts.
・The customer is responsible for repairs and maintenance.
・When using, please keep the specified operating temperature and continuous operating time. If you use it outside the operating temperature and continuous operating time, it will not be covered by warranty.
・Please note that we do not take any responsibilities for breakage, malfunction, injury, accidents or fires caused in connection with the operations of this device.

Other

・We welcome your Inquiry of the Smart Laser CO2. Please feel free to contact us!

このエントリーをはてなブックマークに追加